• Please provide the following to download our free catalog.

  • More Capacity Than Typical AA Buckets
  • Thicker Than Most AA Plastic Buckets
  • Reduces Weight on Elevator up to 80%
  • More Capacity than Cast Iron Buckets
  • Thicker Walls, Heavy Front Digging Lip
  • Heat, Impact and Abrasion Resistant
  • Non-Corrosive, Non-Sparking
  • Easier to Install and Replace
  • Cleaner Discharge
  • Decreases Elevator Down-Time

tiger tuff industrial plastic elevator bucket by maxilift, with sandThe Tiger-Tuff Industrial is a maximum duty industrial elevator bucket, designed and engineered to maximize bucket life and elevated capacity. This will reduce downtime and lower maintenance costs. The Tiger-Tuff Industrial bucket has the thickest lip, back wall and corners to maximize bucket life and maintain capacity. Standard spacing is projection x 2. The most common applications include aggregate, sand, gravel, coal, gypsum, limestone, clay, concrete and many, many more. The Tiger-Tuff Industrial is the maximum duty industrial bucket for your most demanding industrial applications. 

Other Considerations

DRILLING: Elevator buckets are manufactured without a drill pattern. Special drilling or punching can be accommodated upon customer request.

VENTING: Available as needed. See venting options in our catalog.

DIGGER BUCKETS: Use slightly larger metal digger elevator buckets to help loosen material in the elevator boot section that has set up or hardened, thereby reducing abrasion on the plastic buckets. Call for details on Metal Digger elevator bucket options.

SPACING: PROJECTION x 2 = STANDARD VERTICAL SPACING (depending on material and speeds, smaller and large spacing may be used).

INSTALLATION: Use a #1 standard elevator bolt or Sabre-Tooth elevator bolt for installation. Designed to be used with fender or flat and lock washers and hex or locking nuts. If buckets are being installed on chain, use hex head bolts, nuts and washers.

FDA: Both the urethane and polyethylene are designed to FDA specifications for direct contact with food products. Special food grade nylon is also available for high heat applications.

Tiger-Tuff Industrial Size Chart

WordPress Table Plugin

Recommended Uses

(Recommended but not restricted to handling these specific products)

Aggregate

Cement

Coal

Fertilizer

Gravel

Perlite

Potash

Sand

Sawdust

 

Poly

tiger tuff industrial plastic elevator bucket by maxilift

Application:

Grains & Food Products Temperature

Range:

-60F to +180F(210F intermittent)

FDA Approved Material:

Yes

Comments:

Economical, high density polyethylene. FDA approved material for handling food grade products.

Nylon

tiger tuff industrial plastic elevator bucket

Application:

Hot, high impact, abrasive dense products

Range:

-60°F to +300°F (350°F intermittent)

FDA Approved Material:

No

Comments:

Best for high heat applications, with tough impact and abrasion needs.

Urethane

tiger tuff industrial plastic elevator bucket

Application:

Heavy, abrasion, sticky materials

Range:

-60F to +180F(210F intermittent)

FDA Approved Material:

Yes

Comments:

Most flexible and abrasion resistant. Resists product sticking and sharp cutting particles.

FDA Nylon

tiger tuff industrial plastic elevator bucket by maxilift

Application:

Hot, high impact, abrasive food grade products

Range:

-60F to +300F

FDA Approved Material:

Yes

Comments:

Best for high heat food grade applications, with tough impact and abrasion needs.

Venting an elevator bucket aids in bucket fill and discharge with light, fluffy materials. Lightweight, fluffy materials, those that are extremely dense or flow poorly can be difficult to handle in bucket elevators at high speeds. Because these materials tend to trap air when being handled by an elevator bucket, venting provides air relief to assist in their filling and discharge. Commodities for venting include flours, meals, feed mash, DDG’s  or screenings. As these materials enter the bucket, air is released through a series of vent holes in the bottom of the bucket allowing for a more complete fill. These vent holes also allow air to re-enter the bucket, which facilitates full release of product into the discharge. Standard hole diameter is equal to the size of the bolt mounting holes in vent pattern #1, all other vent patterns will have 11/32” diameter holes unless otherwise requested by the customer. When elevating powdery materials such as cement in the Tiger-Tuff, a minimum of two rows of 3/8″ diameter vent holes are recommended to help ensure that the material will discharge cleanly.

ADDITIONAL SPECIAL DRILLING AND VENTING CHARGES

  • Drilling any diameter hole over 13/32″
  • Bolt Hole centers closer than 1-3/4″
  • Side drilled buckets except standard peanut buckets
  • Special Venting requirements such as extra holes, change in hole diameter, etc.
  • Quoted prices subject to change due to special drilling and venting requirements

#1 Vent

Same holes in body as bolt mounting holes.

#2 Vent

One row of holes on 1-1/8″centers

#3 Vent

Two rows of holes on 1-1/8″centers.

#4 Vent

Same as #3, plus three holes in each end cap.

Custom Vent

Vented as required.

Please call for guidance on bucket venting.

Tiger-Tuff Industrial Buckets

What Makes Tiger-Tuff Industrial so Tough?

Tiger-Tuff is the ultimate maximum duty bucket for industrial applications.

tiger-tuff industrial elevator bucket highlights, by maxilift
Buckets, Belting, Splices & Bolts all in one!

Complete your Build

A single shipment, on a single invoice, from a single source: Maxi-Lift. For a limited time only, Maxi-Lift is offering 3% OFF on new bundle orders. Contact us today or call (800) 527-0657 for more information!

Contact a Sales Rep